Tile roofing
Architectural shingles
Metal roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
CertainTeed Gutter Replacement: The Dallas Owner’s Guide
We stock and install CertainTeed-compatible gutter replacement components across Dallas, with most single-side replacements running $450 – $1,100 installed depending on length, profile, and whether fascia repair is needed. Same-day or next-day installation is typical once we confirm the profile match, and every job starts with a written price before we touch the roofline. Most Dallas homeowners discover the failure the hard way: a gutter pulling away from the fascia after a spring storm, water spilling over the edge during a downpour, or a visible crack that’s been quietly leaking into the soffit for months. CertainTeed’s roofline products are solid, but no gutter survives North Texas hail and 100-degree summers without eventually showing its age.
Tilehurst Roofing Dallas is an independent service provider, not affiliated with CertainTeed. We carry CertainTeed roofline profiles and can source OEM or quality aftermarket equivalents, and we match the product to your existing run so the repair disappears into the line.
Which CertainTeed Models This Applies To
CertainTeed manufactures gutters and accessories under several roofline lines, and the compatibility gotcha in Dallas is profile matching. The most common lines we see on homes here are CertainTeed HiddenHanger, Contractor Series, and the Building Products K-Style 5-inch and 6-inch profiles. The 5-inch K-style is the workhorse on Dallas single-family homes; the 6-inch profile shows up on larger roof planes and commercial-bay residential builds. Profile matters more than the brand label stamped on the old trough. We measure the top opening, the depth from top lip to bottom bead, and the hanger spacing before quoting a replacement run, because installing a 5-inch gutter where a 6-inch was carrying stormwater will fail under the first real cloudburst.
For OEM CertainTeed replacements, the hanger style is the second decision point. Older runs used exposed bracket-and-ferrule hangers; newer installs favor hidden hangers that clip inside the gutter lip. Hidden hangers hold better in Dallas wind, but they require the matching profile geometry to seat correctly. If the old fascia board is rotted behind the gutter, we’ll tell you before we quote, because new gutters on bad lumber is a repair that fails inside six months. For homeowners open to aftermarket, GAF and Owens Corning make profile-compatible aluminum troughs that match CertainTeed geometry at a slightly lower material cost, and we carry both on the truck.
Styles & brands we work with
Signs Your CertainTeed Gutter Replacement Is Failing
- Gutter pulling away from the fascia with visible screw or hanger gaps. Dallas spring storms and summer thermal cycling work hangers loose over time. Once the gutter tilts, water sheets behind it and rots the fascia board.
- Water spilling over the outer lip during moderate rain, not just heavy storms. That usually means the run has lost slope, either from sagging hangers or from a tree branch resting on it. A gutter that can’t carry water to the downspout is costing you fascia, soffit, and foundation protection.
- Cracks at the seams or visible rust streaks down the face. Aluminum doesn’t rust, but the steel screws and hangers do. A rust streak is usually a fastener failure, and the crack is where the metal has been flexing for years.
- Pooling water near the foundation after rain, with corresponding damp spots on drywall inside. The gutter isn’t directing water away; it’s dumping it straight down. In Dallas clay soil, that means foundation movement, and foundation work costs more than any gutter replacement.
- Daylight visible through the trough from below, or granule-heavy sediment from the shingles collecting in the gutter. A cracked gutter and clogged downspout often travel together. Once the trough splits, even a partial clog becomes a full overflow.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Dallas homes, a standard CertainTeed-compatible 5-inch K-style gutter run costs $450 – $850 installed for most single-side replacements up to 40 linear feet, including downspout elbows and end caps. A 6-inch profile or a run over 60 linear feet typically lands between $800 – $1,100. If the fascia board behind the gutter is rotted and needs replacement, that adds $150 – $400 depending on length and whether we’re replacing or reinforcing.
| Scope | Typical Dallas Installed Price |
|---|---|
| Single-side 5-inch replacement, up to 40 linear feet | $450 – $850 |
| 6-inch profile or 60+ linear foot run | $800 – $1,100 |
| Fascia repair or replacement behind gutter | $150 – $400 add-on |
| Downspout extension or diverter | $75 – $175 per section |
Every quote includes removal and disposal of the old run, the new CertainTeed-compatible trough, hidden hangers or bracket upgrade, sealant, downspout reconnection, and a written workmanship guarantee delivered before the crew leaves. Material choice is always on the table: CertainTeed OEM or aftermarket GAF and Owens Corning equivalents if you want the same profile at a different price point. Greg Holloway walks every Dallas roofline personally before we quote a number, and the price you get is the price on the invoice.
DIY or Call Us?
Most gutter replacement isn’t a high-tension hazard like garage door springs, but it’s still ladder work on a roofline, and that’s where Dallas homeowners get hurt every year. What you can safely check from the ground: whether the gutter is visibly sagging or separated, whether downspouts are clear, and whether water is pooling at the foundation after rain. What you shouldn’t attempt on a ladder: removing a 40-foot aluminum run that’s under tension from bent hangers, working near the roofline while balancing a new trough over your head, or sealing seams on a second-story eave.
If you’re comfortable on a ladder and the run is short and single-story, a homeowner can swap a section in a Saturday afternoon. But the profile has to match exactly, the slope has to be reset, and the hangers need to land on solid wood or into a rafter tail, not just drywall-soft fascia. Most Dallas homes we see have had at least one previous gutter “fix” that failed because someone hung new gutters on rotted fascia or mismatched the profile. Price before we touch it. That’s just how a roof conversation ought to start. Call (903) 499-4275 and we’ll walk the line and give you a written number.
FAQs
Aluminum K-style gutters typically last 15 – 20 years in the Dallas climate, but the hangers and fasteners usually fail first, between years 8 and 12. Hail, thermal cycling, and wind are the main enemies. We’ll tell you if the trough itself still has life and only the hangers need a refresh. That’s a $150 – $300 fix instead of a full replacement.
Yes, if the crack is at a seam or end cap and the metal around it is still sound, we can reseal and re-hang the run. If the trough is cracked through the body or the profile has flattened from repeated bending, replacement is the only fix that holds. Call (903) 499-4275 and we’ll give you a straight read.
Most single-side replacements take 2 – 4 hours including removal, disposal, and re-sloping. If we’re replacing fascia board or swapping a full house’s gutter system, expect a full day. We’ll give you a written window before the crew arrives.
Yes, we carry 5-inch and 6-inch CertainTeed-compatible profiles plus GAF and Owens Corning equivalents on most Dallas runs. If you have an uncommon profile or color, we’ll source it and schedule the install once it’s in hand. You’ll know the day and the price before we start.
Written by Greg Holloway, Owner, Tilehurst Roofing Dallas at Tilehurst Roofing Dallas, serving Dallas and nearby areas.